View 5713R5KL50XX_1200523.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MODEL SERIES 5710
3" Diameter Single Turn Wirewound Precision Potentiometer
MODEL STYLES
2
5711 5713
ELECTRICAL
1/4" Shaft, 1/2" Bushing 1/4" Shaft, Servo
Resistance Range, Ohms Standard Resistance Tolerance Minimum Practical Resistance Tolerance Independent Linearity Minimum Practical Independent Linearity
Power Rating, Watts Dielectric Strength Insulation Resistance, Minimum Noise, Maximum Actual Electrical Travel Tap Tolerance End Voltage, Maximum
ENVIRONMENTAL (MIL-R-12934)
25 to 145K 5% 1% 0.5% 0.5%, <75 Ohms 0.25%, 75-249 Ohms 0.15%, 250-6,999 Ohms 0.075%, 7K Ohms 5.0 at 40C derating to 0 at 105C 1,000V rms 1,000 Megohms 100 Ohms 358 1 1 Within Std. Linearity Tolerance
Operating Temperature Range Temperature Cycling Shock, 6ms Half Sine Vibration Moisture High Temperature Exposure Rotational Life Rotational Load Life
Specifications subject to change without notice.
Static: -65C to +105C Dynamic: -40C to +125C 5 cycles, -65C to +105C 100G's 5G's, 10 to 500 Hz Ten 24 hour cycles 1,000 hours at 105C 1 Mil. Shaft Rev. 1 mil. shaft rev. plus 900 hrs. at rated wattage at 40C
2-55
Model 5710 Series
MECHANICAL
Total Mechanical Travel Number of Cups, Maximum Weight, Nominal Backlash, Maximum Shaft End Play, Maximum Shaft Runout, T.I.R., Maximum Pilot Diameter Runout, T.I.R., Maximum Lateral Runout, T.I.R., Maximum Shaft Radial Play, Maximum Starting Torque, Maximum Running Torque, Maximum
STANDARD RESISTANCE VALUES, OHMS
360 Continuous 4 5.8 oz. Single Cup 1.3 oz. Each Added Cup 1 .005" 5711 5713 .0005" .001" .002" .0015" .004" .101" .004" .002" 1.5 oz.-in. 1.3 oz.-in. 1.2 oz.-in. 0.7 oz.-in.
Total Resistance 1K 2K 5K 10K 20K 50K 100K
Theoretical Resolution (% Nominal) 0.062 0.050 0.038 0.031 0.027 0.024 0.022
Tempco of Wire 130 ppm/C 130 ppm/C 130 ppm/C 130 ppm/C 130 ppm/C 20 ppm/C 20 ppm/C
METRIC CONVERSIONS
1 in. 1 oz.
25.4 mm 28.4 gm
1 oz.-in. 1 lb.-in.
0,007 N-m 0,113 N-m
2-56
Model 5710 Series
OUTLINE DIMENSIONS (Inch/mm)
Model 5711 - Bushing Mount
Dimensions shown are with 1 cup, for each additional cup: increase "RS" by .562 14.3 .562.002 increase "L" by 14.3 0.05
"RS" "L"
1.482.031 37.64 0.79 Mounting Surface .982.020 24.9 0.51 .469 Min. 11.9 1.500.031 38.10 0.79
90 Max. Clamp CW Ears CCW Slider 1.750 R. Max. 44.45
2
.2497 + .0000 - .0003 Dia. 6.342 + 0.000 - 0.008
3.000 .016 Dia. 76.20 0.41
1.375.016 Dia. 34.93 0.41
+
+
.062 + .000 - .010 1.58 + 0.00 - 0.25
Chamfer .016 Max. x 45 0.41 1/2-32 NS Thread .500.016 12.7 0.41
.5937 + .0000 - .0020 Dia. 15.08 + 0.000 - 0.051 .531 .016 13.5 0.41
Locating Hole .129 .005 Dia. x .062 .016 Deep 1.58 0.41 3.28 0.13 Positioned as shown 5
OUTLINE DIMENSIONS (Inch/mm)
Model 5713 - Servo Mount
"RS" "L"
1.520.031 38.61 0.79 1.020.015 25.91 0.38 .500 12.7 Min. Mounting Surface .625.031 15.9 0.79
Dimensions shown are with 1 cup, for each additional cup: increase "RS" by .562 14.3 .562.002 increase "L" by 14.3 0.05
90 Max. Clamp CW Ears CCW Slider 1.750 R. Max. 44.45
3.000 .016 Dia. 76.20 0.41
.2497 + .0000 - .0003 Dia. 6.342 + 0.000 - 0.008
3.000.005 Dia. 76.20 0.13
+
Chamfer .016 Max. x 45 0.41 2.785 73.03 Dia. Max. .073 Min. 1.85
2.875 + .000 - .001 Dia. 73.03 + 0.00 - 0.03
.093 .005 2.36 0.13 .062 .005 1.58 0.13
2-57
Model 5710 Series
SPECIAL FEATURES
Center Tap Linearity Tape Rear Shaft Extension Flatted Shaft Slotted Shaft Anti-Fungus Treatment
ORDERING INFORMATION
CT LT RS FS SS AF
5711 R 10K L.50 XX Model Series Resistance Prefix Resistance Value Linearity Optional Special Feature Code
CIRCUIT DIAGRAM
NOTES
Metric equivalents, based on 1 inch = 25.4mm are rounded to the same number of significant figures as in the original English units and are provided for general information only. Tolerances unless otherwise specified: Linear = .01 inches (.25mm) Angular = 2 degrees
(S) (CCW) (CW)
INCH mm
2-58
Model 5710 Series

▲Up To Search▲

Price & Availability of 5713R5KL50XX

	To Download 5713R5KL50XX Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .